Air Valve |
|
|
|
|
Housing |
|
|
|
|
|
Switch |
|
|
|
|
|
Assembly |
|
|
|
|
Switch |
|
|
|
|
|
Bracket |
|
|
|
|
|
Tubing |
|
|
|
|
|
Connection |
|
|
|
|
Air Cylinder |
|
|
|
|
Actuator |
|
|
|
|
Email:smt@smtsky.com,Website:www.smtsky.com |
Block |
|
|
|
|
|
|
|
|
|
|
|
Page 41 |
|
|
|
|
|
TECHNICAL PUBLICATIONS |
|
|
|
Dual Head Board Handling System L/R T46365904 Rev. J |
This Document Supports Assembly 46365904 Rev. J |
Bad Board Hopper Disassembly/Assembly |
|
1. Remove the four 1/4 - 20 x 1/2 button head screws and lock washers |
that secure the shafts to the hopper frame and remove the guide assembly |
from the frame. |
|
|
|
|
Email:smt@smtsky.com,Website:www.smtsky.com |
2. Remove the two 6 - 32 x 3/8 cap screws and lock washers that secure |
the collar clamps to the shafts. Loosen the two 6 - 32 cap screws and |
lock washers that lock the collar clamps to the shafts then slide the collar |
clamps and front guide assembly from the shafts. |
3. If necessary, remove extension spring and the two shoulder screws that |
secure the hinge to the front guide and remove the hinge. |
4. Remove the eight 8 - 32 x 1/2 cap screws and lock washers that secure |
the two linear bearings to the rear guide assembly and remove the linear |
bearings, shafts and rear guide assembly. |
|
5. If necessary, remove the four 8 - 32 x 5/16 flat head screws that secure |
Email:smt@smtsky.com,Website:www.smtsky.com |
the rear guide bracket to the rear guide and remove the rear guide |
bracket from the rear guide. |
|
|
6. If necessary, remove the two shoulder screws that secure the hinge to |
the rear guide and remove the hinge. |
|
Rear Guide Bracket |
|
|
|
Rear Guide |
|
|
|
|
Front Guide |
|
|
|
|
Shaft |
|
|
|
|
|
Hopper Frame |
|
|
|
|
Hinge |
|
|
|
|
|
Email:smt@smtsky.com,Website:www.smtsky.com |
Hinge |
|
|
|
|
|
Shoulder Screw |
|
|
|
|
Shoulder Screw |
|
|
|
|
Collar Clamp Linear Bearing |
|
|
|
|
|
|
|
|
Page 42 |
|
|
|
|
|
TECHNICAL PUBLICATIONS |
|
|
|
T46365904 Rev. J |
|
|
|
|
Dual Head Board Handling System L/R |
|
7 |
|
|
|
|
|
Email:smt@smtsky.com,Website:www.smtsky.com |
Inspect all parts for wear or damage and replace as necessary. |
8 |
|
|
|
|
|
Install the hinges to the front and rear guides using the four shoulder |
screws. |
|
|
|
|
|
9 |
|
|
|
|
|
Install the rear guide bracket to the rear guide using the four 8 - 32 x 5/ |
16 flat head screws. |
|
|
|
10 |
|
|
|
|
|
Slide a linear bearing on each shaft then insert them through the rear |
guide assembly as shown. Secure the linear bearings to the rear guide |
Email:smt@smtsky.com,Website:www.smtsky.com |